|
Climbing
accessories
We supply
and install climbing wall holds, fixings, belays, belay ropes, carabiners,
harnesses and hats.
|
Climbing wall holds are supplied in different sizes
and shapes. All feature a moulded resin hold with a highgrip surface and
bolt hole (2 on larger holds to stop them turning). Holds feature an internal
safety device which holds the unit together in the unlikely event of one
cracking around the bolt fixing (if overtightened). This stops the 2 halves
breaking off and falling and possibly injuring someone.
|
Climbing wall holds shaped as the letters of the alphabet
- make learning fun! All feature a moulded resin hold with a highgrip
surface and bolt hole (2 on larger holds to stop them turning). Holds
feature an internal safety device which holds the unit together in the
unlikely event of one cracking around the bolt fixing (if overtightened).
This stops the 2 halves breaking off and falling and possibly injuring
someone.
|
Climbing wall holds shaped as numbers - make learning
fun!. All feature a moulded resin hold with a highgrip surface and bolt
hole (2 on larger holds to stop them turning). Holds feature an internal
safety device which holds the unit together in the unlikely event of one
cracking around the bolt fixing (if overtightened). This stops the 2 halves
breaking off and falling and possibly injuring someone.
|
Set of 48 climbing wall holds for club use in different
sizes and shapes. All feature a moulded resin hold with a highgrip surface
and bolt hole (2 on larger holds to stop them turning). Holds feature
an internal safety device which holds the unit together in the unlikely
event of one cracking around the bolt fixing (if overtightened). This
stops the 2 halves breaking off and falling and possibly injuring someone.
|
Equal Y hang belay, stainless steel with chains ring
and 12mm karabiner. This spreads the load to 2 fixings on the same row.
|
Offset Y hang belay, stainless steel with chain, ring
and karabiner. This spreads the load to 2 fixings on different rows for
uneven walls so the fixings are on the same plane.
|
Single point fixed belay, stainless steel with ring.
|
4 point steel belay plate for spreading the load to 4
separate fixings. Ideal for use on 7kN block to achieve the required strength.
This is the plate only which comes with 2 welded nuts for attaching the
double belay CLI15 which must be ordered as well.
|
Ballast bag to increase the weight of a belayer. The bag
weighs up to 25kg when filled with sand or gravel and sits adjacent to
the belayer and is attached via a lanyard to the belayer's harness. The
bag excludes the ballast material and the lanyard.
|
Countersunk M10
bolt for fixing holds to the wall or panel. These are available in 35mm,
50mm or 70mm lengths depending on the type of wall and fixing used. The
wall or panel must have the correct insert
|
Special expansion anchor for fitting into brick or block
walls for installing climbing wall holds, size 44/10mm. It is essential
these are installed by a professional.
|
6mm allen key with a T handle for tightening holds onto
a wall. The T bar enables the hold to be tightened sufficiently for safe
use but helps prevent overtightening which can lead to cracked holds and
over expanded wall fixings
|
High friction paint for painting brick or block walls
to improve the look and feel for climbing and traversing walls. Available
in 2.5 or 5ltr only in white, yellow, red, blue, green, light and dark
grey. Paint includes aggregate so must be stirred well. Coverage approx
6-10m2 for a 5ltr tin.
|
A specific PVC covered mat for climbing walls with a sandwich
construction foam with 20mm polyethylene foam on either side of a polyurethane
core. This provides a firmer base than standard crash mat foam and is
more stable when landing on it (when you land feet first on a crash mat
there is a risk of ankle "roll over" like landing on an uneven
surface where you can easily sprain or break an ankle). There are also
50mm wide velcro tabs on all 4 sides so the mats can be joined to create
a larger landing area (with the tabs on the top side so feet don't go
in between the mats). We recommend the mats extend 2m from the climbing
wall.
Mat
is 2m long x 1m wide x 200mm deep.
|
Plug together 500mm square tiles which are ideal for setting
out around the movable boulders. Edge tiles have 1 ramped edge and corner
tiles have 2. Tiles are 50mm thick.
|
Lightweight adjustable webbing harness for climbers and
belayers with precise adjustment with double back buckles on the waist
belt and leg loops. Suitable for children over 9 years to adults (sizes
1 and 2). (For 5-10 years the Simba or Oustiti full body harness is required).
Weight 0.425kg
|
Auto braking device for belayers. If a fall happens the
pivoting cam inside the device facilitates braking. The Grigri is attached
to the belayers harness with the belay rope passing through the device.
When locked this allows the belayer's full weight (plus ballast bag if
attached) to be used to counterbalance the climber without all the load
passing through the belayer's hands.
|
Lightweight and robust helmet, injection moulded polycarbonate
with expanded polypropylene foam inner for protection.Available in white,
blue and orange with adjustable strap at the back to fit most head sizes.
Size 1 48-56cm, size 2 53-61cm
Weight 315-345g
|
Dinamic 10.5mm diameter low stretch climbing rope. Belay
ropes must be used with the correct size carabiner through which they
pass. We recommend a belay rope 2.5 to 3 times as long as the climbing
wall height. Price per metre
|
Friction belay for use on climbing walls which removes
the need for a belayer. The device is fitted to the belay point and the
belay rope pulled out to attach to the climber. If the climber falls at
any stage the autobelay lowers the climber at a controlled rate slowly
back to the ground.
|
For
crashmats, rubber tiles or safety surfacing please refer to the relevant
section in product index or contact our sales team. We can also carry out
annual testing and certification of climbing walls in accordance with DCIJS/156/99 |